Plumbing 101: A Necessity for Bathtub Installation
Plumbing 101: A Necessity for Bathtub Installation
Blog Article
The article listed below in relation to How to Install a Bathtub Yourself is really intriguing. Read it for yourself and figure out what you think of it.
Setting up a bath tub isn't exactly brain surgery, however it does need strong plumbing, woodworking, and also occasionally, tiling skills. Replacing an old bath tub with a brand-new one is likewise a moderately tough task. If the old tub is conveniently obtainable, the project can relocate speedily; if you need to open a wall surface to remove the old bathtub as well as position the brand-new bathtub, the task is a lot harder. In either case, the project is within a residence handyman's abilities, although you will certainly need an assistant to vacate the old tub as well as embeded in the brand-new one. Make certain you have qualified yourself for the task as well as are comfortable attempting it. Instead of working with a contractor to take control of a halfway-completed project, it is much better to think about employing one prior to you start. Possibilities are you may need an expert plumber to make tube links.
This short article will certainly aid you mount a brand-new bath tub in your shower room if you have currently purchased a brand-new tub and also do not require to alter the arrangement of your previous water pipes.
Your tools as well as product checklist should comprise the following:
Preparing for the Installation
First of all, the sustaining structure supplied with the bathroom needs to be fitted (if needed) according to the producer's guidelines. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is essential to make sure that if the tap includes a plastic washer, it is fitted in between the bath and the taps. On a plastic bath, it is additionally reasonable to fit a supporting plate under the faucets device to avoid pressure on the bathtub.
Fit the versatile faucet connectors to the bottom of the two faucets utilizing 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet through the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Make certain you utilize every one of the provided washers.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom ought to now be ready to be suited its last position.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installment, after that the first thing you need to do is disconnect the water supply. After doing so, activate the faucets to drain pipes any type of water continuing to be in the system. The procedure of getting rid of the existing faucets can be rather bothersome due to the restricted access that is usually the situation.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the faucets. Have a towel prepared for the remaining water that will certainly come from the pipelines. Once the supply pipelines have been removed, use the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from transforming during this process. Once the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any kind of old sealing compound.
Before proceeding to fit the new taps, contrast the pipe links on the old faucets to the brand-new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Setting up the Bathtub
Using the two wood boards under its feet, put the bath tub in the required placement. The wood boards are useful in evenly spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four tiny factors.
The following goal is to make certain that the bathtub is leveled all round. This can be attained by inspecting the spirit level and readjusting the feet on the tub until the spirit level checks out level.
To mount taps, fit the bottom of the furthest versatile tap adapter to the proper supply pipe by making a compression join; after that do the exact same for the various other faucet.
Turn on the water system and also examine all joints and also new pipework for leakages and tighten them if needed. Fill up the bath tub and also inspect the overflow electrical outlet and the regular outlet for leakages.
Finally, take care of the bath paneling as described in the producer's instruction manual. Tiling as well as sealing around the bathtub must wait until the bathtub has actually been made use of at least when as this will resolve it right into its last position.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly require a plastic port to avoid damages to the thread. One end of the adapter fits on the plastic tail of the faucet and also the other end provides a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will require lowering couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, place the tap in the placing opening in the bath/basin ensuring that the washers remain in location between the faucet and the sink. Protect the tap in position with the supplier provided backnut. As soon as the faucet is securely in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical faucet ports. The previous kind should be connected to the tap ends first, tightening up only by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the location where the bathroom meets the tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to fracture an inflexible seal, causing the water to permeate the wall between the bathroom as well as the tiling, causing problems with wetness as well as feasible leakages to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures as well as fittings. They are offered in tubes and cartridges, as well as can securing spaces up to a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with twists of soaked paper or soft rope. Remember to constantly load the tub with water before sealing, to enable the activity experienced when the tub is in usage. The sealant can split relatively early if you do not take into account this movement before sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally conveniently readily available on the marketplace. It is advisable to fit the floor tiles utilizing water-resistant or waterproof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been made aware of that article about How to Install a Bathtub Yourself from a friend on another domain. Those who enjoyed reading our page kindly don't forget to share it. Thank you so much for taking the time to read it.
Request plumbing analysis. Report this page